• Зарегестрируйтесь что бы увидеть контакты услуг и продавцов ПАВ

    You need to register to see contacts RC sellers and services.

SCREW Synthesis: Synthesis: SCREW

DEMIURGE

Well-known member
Joined
20/5/23
Messages
230
Reputation +/-
58
Reaction score
155
Points
293
Synthesis synthesis. The method 1 is:

The screw is synthesized by ephedrine, red phosphorus and crystalline iodine: In the synthesis of it, ephedrine, red phosphorus and crystalline Iodine are used:

1. 1. Ephedrine, as well as pseudoephedrine are suitable for making a screw. 2. Pseudoephedrine is suitable for making a screw. Is one of the optical isomers that ephedrine has. For a vinvar, there is no difference between pseudoephedrine and ephedrine - the end product from them will be exactly the same. Pseudoephedrine has a less active effect on the central nervous system, while maintaining the strong bronchodilatory properties of the l-isomer. Norephedrine has the same phenylpropanolamine found in Coldact, norepinedrine is about the same phenylpropanolamine. And from it, as well as from koldakt: you can make Amph and cathinone. But there is no possibility to get meth or methcathinone.

2. Red phosphorus. 2. Red phosphorus. 1. Red. Red phosphorus is obtained by the extraction (obtaining) of matchboxes.

It is necessary to make the incendiary coating on matchboxes. The composition of it:

1. Phosphorus 1. P (red phosphorus). 1. P (red.

2. 2. Sb2S3 (antimony sulfide) 1. Sb2S3 (antimony (III) sulfide).

3. 1. 3. Fe2O3 (iron(III) oxide, crocus). 2. Fe2O3 (iron(III) oxide, crocus.

4. 4 sio2. 5. Silica.

5. Glue. 5. Glue.

ATTENTION: do not spare hydrochloric acid for purification of phosphorus and time for decanting, otherwise all these metals and sulfur, in contact with HI or HCl will go into solution.

The Process: Process:

1. 5. Choose 5 boxes of matches. 1. Buy 5 boxes of matches. A can of hydrochloric acid (36% -38%) is purchased in radio products.

2. In order to fill acid, we use a blade. We cut off the "graters" from the boxes with as little paper as possible and put them on an acid plate (without gold or silver stripes), then place it on one plate (without any coloring and no drawings).

3. 3. We put the plate in water bath (a bowl / pot with low heat, that is an open pit of water boiling over low heat - this way steam heats the plate). 4. The table is placed in a water bath (a bowl or pan) in whose liquid under high temperature boils.

4. The acid becomes dirty in color and various debris floats in it. 4. The acid becomes dirty in colors and dirty in color. Do not put your face in the plate - HCI vapors are rather unpleasant. For some time, the "graters" will turn red on one side and black on the side where paper was. When we catch this moment, we carefully drain the acid. This is what we do.

5. 5. Rinse with acid, then rinse water. 6. Rinse with water, then rinse with acid. After this, once again fill with acid and put on the table for 5 minutes. In the end, drain the acid and wash again with water. When we put what is left of the graters (dark red thin plates) on the glass, rub it with an electric blade and wash off all dirt. The rest of the dirt will be removed by a syringe with water. At the end of 5 boxes, you should get 350 mg of phosphorus. An obtained from "chirkash" phosphorus is capable of some impurities, so it is recommended to take such an oil by weight 50% more than pure red. In any case, the phosphorus obtained from "chirkash" will contain insignificant impurities and must be poured into the reactor at 50 times more than pure Red.

3. Crystalline iodine. 3. Crystalline iodine. Crystalline iodine is obtained by the extraction of crystalline iodine from an alcohol (pharmacy) solution of iodine:

1. When we take a 20 ml syringe, seal the end. 1. We take one 20 ml syringe and seal the end. In the piston, we make several holes in the piston, wrap the piston with an elastic fabric folded 2 times.

2. In the syringe, pour 17 ml of iodine into a syringe, add 2 ml of water, dripping 12 drops of hydrochloric acid. Then shake lightly and set aside.

3. 2. After settleing in the syringe, an almost transparent layer should be visible from above (if there is no layer, add another 1 ml of water and 5 droplets hydrochloric acid). 4. The liquid after settling into its shell should be clearly reflected from above (if there is no layer, add another 1 ml of water and 5 drops of hydrochloric acid).

4. 5. The piston with the rag and press (to remove all liquid and leave only crystals of Iodine). It poured out what passes through the holes in the piston. At the end of the process, you need to press hard, trying to remove all moisture. After that, carefully remove the piston. In order to sleep, we take a newspaper. We turn the syringe over, and then hit it from above: almost dry Iodine gets enough sleep in this way. In case of the absence of moisture, then put the iodine in an newspaper and squeeze it out.
 
Last edited:
Top Bottom